Full integration in RFEM/RSTAB including import of all relevant internal forces
Intelligent presetting of flexural buckling-specific design parameters
Automatic determination of the distribution of internal forces and classification according to DIN 18800, Part 2
Optional import of buckling lengths from the RF-STABILITY/RSBUCK add-on module. For this, a comfortable graphical selection of the relevant buckling mode is possible
Optimizing Cross-Sections
Optional calculation according to both design methods of DIN 18800, Part 2
Automatic determination of the most unfavorable design location, also for tapered members
Check of c/t-limit values according to DIN 18800, Part 1
Design of any thin-walled RFEM/RSTAB or SHAPE-THIN section for compression and bending without interaction according to the elastic-plastic method
Design of I-shaped rolled and welded sections, I-like sections, box sections, and pipes subjected to bending and compression with iteration according to the elastic-plastic method
Clearly arranged, comprehensible design checks with all intermediate values in the short and long forms
Design of foundation torsion and limitation of gaping joint
Sliding design
Settlement calculation
Bending failure design of the plate and bucket
Punching shear design
Foundation and bucket dimensions can be user-defined or determined by the module. You can edit the determined reinforcement manually. In this case, the designs are updated automatically.
Design-relevant data are entered in two separate windows. Since the RF-/DEFORM module is very clearly arranged, working in it is very easy.
First of all, it is necessary to define the actions to be designed. Then, you can select the members and sets of members manually or graphically and assign the respective allowable limit deformations.
The deformations correspond to deformed member ends or an undeformed system.
It is necessary to enter material, load, and combination data in RFEM/RSTAB in compliance with the design concept specified by SIA 263.
The RFEM/RSTAB material library already contains the relevant materials for SIA. Furthermore, RFEM/RSTAB automatically creates the corresponding load combinations according to SIA 260. However, you can also create all the combinations manually in RFEM/RSTAB.
The RF-/STEEL SIA add-on module requires members and sets of members, as well as load cases, load combinations, and result combinations to be designed. In the next steps, you can adjust the preset definitions of lateral intermediate supports and effective lengths.
In the case of continuous members, it is possible to define individual support conditions and eccentricities of each intermediate node of single members. A special FEA tool then determines the critical loads and moments required for the stability analysis in these situations.
RSBUCK is distinguished by easy handling, clear data arrangement, and great user-friendliness. With only a few mouse clicks, you can define the number of buckling modes to be calculated, as well as the load case to be considered.
Structural data and boundary conditions set in the selected load case are imported automatically from RSTAB. Alternatively, you can edit the imported axial forces or enter new values manually. It is also possible to create further RSBUCK cases in order to perform several analyzes each with different boundary conditions.
For a better result display, it is possible to set the units individually in RSBUCK. If the RSTAB internal forces are not available when starting the RSBUCK module, the program calculates the required internal forces automatically before determining the buckling values.
There are various options available for frame modeling. Graphical representations facilitate the geometry input. Modifications are updated automatically. Basic dimensions as well as geometrical data are entered in tables. During the input, the program checks the conditions required for the beam creation (for example, lamellas forming a curve) according to the defined standard. The most important geometry parameters are updated and displayed.
The relevant timber grade of the material can be selected from the material library. All material grades for glulam, hardwood, poplar and softwood timber specified in EN 1995-1-1 are available. Furthermore, it is possible to generate a strength class with user-defined material properties in order to extend the library. Permanent loads (for example, roof structure) can also be entered using the comprehensive and extensible material library.
Generators integrated in RX-TIMBER Purlin allow for convenient generation of various wind and snow load cases. By clicking the information buttons, the map of wind and snow zones for the relevant country is displayed. The corresponding zone can be selected with a double-click. Load cases can be checked graphically. However, you can enter load specifications manually as well. According to the generated loads, the program automatically creates combinations for the ultimate and serviceability limit states as well as for fire resistance design in the background. The generated combinations can be considered or adjusted by user-defined specifications.
There are various options available for beam modeling. A roof type determines the exact purlin location for wind and snow generation.
Two beam types are available: continuous beam and purlin. If you select the continuous beam, it is possible to define several hinge conditions of the beam. If you select the purlin, it is not possible to modify hinge conditions. In this case, the calculation considers a double cross-section in the coupling zone. In addition, several coupling elements are available in the purlin settings:
Nails (prebored/not prebored)
Ring and plate connectors and bolts
Screw connection with fastening system WT from SFS intec
User-defined specification using characteristic strength
The relevant timber grade of the material can be selected from the material library. All material grades for glulam, hardwood and softwood timber specified in EC 5 are available. Furthermore, you have the option to generate a strength class with user-defined material properties and thus extend the library.A comprehensive and extensible material library can also be used for entering permanent loads (for example, roof structure).
Generators integrated in RX-TIMBER Purlin allow for convenient generation of various wind and snow load cases. By clicking the information buttons, the map of wind and snow zones for the relevant country is displayed. The corresponding zone can be selected with a double-click. Load cases can be checked graphically.
However, you can enter load specifications manually as well. According to the generated loads, the program automatically creates combinations for the ultimate and serviceability limit states as well as for fire resistance design in the background.
There are various options available for beam modeling. Graphical representations facilitate the geometry input. Modifications are updated automatically. Deflection of cantilevers can be set in the serviceability limit state design, independently of the deflection in the span.
In order to enter permanent loads (for example, roof structure), you can use a comprehensive and extensible material library. Generators integrated in RX-TIMBER Purlin allow for convenient generation of various wind and snow load cases.
Load cases are displayed graphically and superimposed in automatically generated load combinations according to EC 5. This way, the required input data are reduced to a minimum. However, you can enter load specifications manually as well.
There are various options available for beam modeling. Graphical representations facilitate the geometry input. Modifications are updated automatically. Deflection of cantilevers can be set in the serviceability limit state design, independently of the deflection in the span.
The relevant timber grade of the material can be selected from the material library. All material grades specified in EN 1995-1-1: 2004 (EC 5) or DIN 1052:2008-12 and the selected National Annex are available for glulam, hardwood, and softwood timber. Furthermore, it is possible to generate a strength class with user-defined material properties in order to extend the library. Permanent loads (for example, roof structure) can also be entered using the comprehensive and extensible material library.
Generators integrated in RX-TIMBER Purlin allow for convenient generation of various wind and snow load cases. Load cases are displayed graphically and superimposed in automatically generated load combinations according to EN 1990, DIN 1055-100, or DIN 1052. This way, the required input data are reduced to a minimum. However, you can enter load specifications manually as well.
The members to be designed are directly imported from RFEM/RSTAB. Load cases, load combinations, and result combinations are assigned, which result in the linear-elastically determined internal forces on the selected members. When considering creeping, the creep-producing load must also be defined. The RFEM/RSTAB materials are preset but can be adjusted in RF-/CONCRETE Columns. The material properties listed in the respective standard are included in the material library.
You can easily define constructional properties of columns as well as other details for determining the required longitudinal and shear reinforcement. The effective length factor ß is to be defined manually, determined automatically by the module, or imported from the RF-STABILITY/RSBUCK add-on module.
The fire resistance design according to EN 1992-1-2 requires various specifications; for example, determination of cross-section sides where burn-off occurs.
The RF-/TOWER Loading add-on module meets the requirements of EN 1991-1-4 / DIN EN 1993-3-1, DIN 1055-4, DIN 4131:1991-11, and DIN V 4131:2008-09. These standards include specifications of dead, wind, maintenance/technician and ice loads (ISO 12494 or DIN 1055-5), as well as variable loads. The standard specifications are preset or available in the libraries.
For the generation of wind loads according to Eurocode, the National Annexes (NA) of the following countries are available:
DIN EN 1991-1-4 (Germany)
CSN EN 1994-1-4 (Czech Republic)
NA to CYS EN 1991-1-4 (Cyprus)
DK EN 1991-1-4 (Denmark)
NBN EN 1991-1-4 (Belgium)
NEN EN 1991-1-4 (Netherlands)
NF EN 1991-1-4 (France)
SFS-EN 1991-1-4 (Finland)
SIST EN 1991-1-4 (Slovenia)
SR EN 1991-1-4 (Romania)
SS EN 1991-1-4 (Singapore)
SS-EN 1991-1-4 (Sweden)
STN EN 1991-1-4 (Slovakia)
UNI EN 1991-1-4 (Italy)
It is possible to generate individual load situations: You can set the wind pressure, wind direction, or ice loads manually, or import them from tables.
The input parameters relevant for the selected standards are suggested by the program in accordance with the rules. Furthermore, it is possible to enter response spectra manually. Dynamic load cases define a direction of response spectra effects and the structure eigenvalues that are relevant for the analysis.
After you have selected the joint type, the connection category, and the design standard in the first input window, you can define the node to be imported from RFEM/RSTAB and to be used for the design of the joint in Window 1.2. Optionally, you can define the connection geometry manually.
In the other input windows, you can then define the parameters of the connection, such as The loading is imported from RFEM/RSTAB or, in the case of manual joint definition, loads are entered.
After you have selected the anchorage type and the design standard in the first input window, define the node in Window 1.2 that is to be imported from RFEM/RSTAB and where the footing anchorage is to be designed.
Optionally, you can define the column cross-section and material manually. In the next input windows, you can define the parameters of the base point, such as The loading is imported from RFEM/RSTAB or, in the case of a manual joint definition, the loads are entered.
Input windows require all data necessary for determination of natural frequencies, such as mass shapes and eigenvalue solvers.
The RF-/DYNAM Pro - Natural Vibrations add-on module determines the lowest eigenvalues of the structure. The number of eigenvalues can be adjusted. Masses are directly imported from load cases or load combinations (with optional consideration of total masses or a load component in the direction of gravity).
Additional masses can be defined manually at nodes, lines, members, or surfaces. Furthermore, it is possible to control the stiffness matrix by importing normal forces or stiffness modifications of a load case or combination.
The design includes detailed information about analyzed internal forces, validity limits, and design conditions. Design failures are clearly marked in the result overview.
All input and result data are also documented in the general RFEM/RSTAB printout report. Separate design cases allow flexible analysis of the individual components in large structures.
Integration in RFEM/RSTAB with automatic geometry recognition and transfer of internal forces
Optional manual definition of connections
Extensive library of hollow sections for chords and struts:
Round sections
Square sections
Rectangular sections
Implemented steel grades: S 235, S 275, S 355, S 420, S 450, and S 460
Various types of connections available, depending on the standard specifications:
K connection (gap/overlapping)
KK connection (spatial)
N connection (gap/overlapping)
KT connection (gap/overlapping)
DK connection (gap/overlapping)
T connection (planar)
TT connection (spatial)
Y connection (planar)
X connection (planar)
XX connection (spatial)
Selection of partial safety factors according to the National Annex for Germany, Austria, Czech Republic, Slovakia, Poland, Slovenia, Switzerland, or Denmark
Adjustable angles between struts and chords
Optional chord rotation of 90° for rectangular hollow sections
Consideration of gaps between struts or overlapping struts
Optional consideration of additional nodal forces
Design of the connection as the maximum load-bearing capacity of the struts of a truss for axial forces and bending moments
Members of triangular and quadrilateral lattice towers are allocated automatically, provided that the lattice tower was generated in the RF-/TOWER Structure and RF-/TOWER Equipment add-on modules.
However, it is also possible to allocate the members manually. In RF-/TOWER Design, you can use the effective lengths of truss members generated in the RF-/TOWER Effective Lengths add-on module. Manual input is also possible.
According to the EN 1993-3-1 and EN 50341 standards, different bracing cases and support types can be specified for the leg members and bracing members.
Initially, it is necessary to define material data, panel dimensions, and boundary conditions (hinged, built-in, unsupported, hinged-elastic). It is possible to transfer the data from RFEM/RSTAB. Then, boundary stresses can be either defined for each load case manually or imported from RFEM/RSTAB.
Stiffeners are modeled as spatially effective surface elements that are eccentrically connected to the plate. Therefore, it is not necessary to consider the stiffener eccentricities by effective widths. The bending, shear, strain, and St. Venant stiffness of stiffeners as well as the Bredt stiffness of closed stiffeners is determined automatically in a 3D model.
The data specified in RFEM/RSTAB concerning material, loads, and load combinations must comply with the design concept of the Eurocode. The RFEM/RSTAB material library already contains the relevant materials. Furthermore, RFEM/RSTAB allows for automatic creation of load and result combinations in accordance with the Eurocode. It is also possible to create the combinations manually.
In the RF-/ALUMINUM add-on module, you must first select the members and sets of members to be designed, as well as the load cases, load combinations, and result combinations. In the subsequent input windows, you can adjust preset definitions of lateral intermediate supports and effective lengths.
When using continuous members, you can define individual support conditions and eccentricities for each intermediate node of the single members. A special FEA tool determines the critical loads and moments required for the stability analysis.
It is necessary to enter material, load, and combination data in RFEM/RSTAB in compliance with the design concept specified by CSA S16. The RFEM/RSTAB material library already contains materials relevant for the Canadian standard.
RFEM/RSTAB automatically creates the corresponding load combinations according to the Canadian standard. However, you can also create all the combinations manually in RFEM/RSTAB. The RF-/STEEL CSA add-on module requires members and sets of members, as well as load cases, load combinations, and result combinations to be designed.
In the subsequent input windows, you can adjust preset definitions of lateral intermediate supports and effective lengths. In the case of continuous members, it is possible to define individual support conditions and eccentricities of each intermediate node of single members. A special FEA tool then determines the critical loads and moments required for the stability analysis in these situations.
It is necessary to enter material, load, and combination data in RFEM/RSTAB in compliance with the design concept specified by BS 5950 (or Eurocode). The RFEM/RSTAB material library already contains relevant materials for BS 5950.
RFEM/RSTAB automatically creates the corresponding load combinations according to BS 5950 (or Eurocode). However, you can also create all the combinations manually in RFEM/RSTAB. The RF-/STEEL BS add-on module requires members and sets of members, as well as load cases, load combinations, and result combinations to be designed.
In the subsequent input windows, you can adjust preset definitions of lateral intermediate supports and effective lengths. In the case of continuous members, it is possible to define individual support conditions and eccentricities of each intermediate node of single members. A special FEA tool then determines the critical loads and moments required for the stability analysis in these situations.
It is necessary to enter material, load, and combination data in RFEM/RSTAB in compliance with the design concept specified by IS 800. The RFEM/RSTAB material library already contains relevant materials for IS 800.
RFEM/RSTAB automatically creates the corresponding load combinations according to IS 800. However, you can also create all the combinations manually in RFEM/RSTAB. The RF-/STEEL IS add-on module requires members and sets of members as well as load cases, load combinations, and result combinations to be designed.
In the subsequent input windows, you can adjust preset definitions of lateral intermediate supports and effective lengths. In the case of continuous members, it is possible to define individual support conditions and eccentricities of each intermediate node of single members. A special FEA tool determines critical loads and moments required for the stability analysis.
Comprehensive and easy options in the individual input windows facilitate the representation of the structural system:
Nodal Supports
The support type of each node is editable.
It is possible to define a warp stiffening on each node. The resulting warp spring is determined automatically using the input parameters.
Elastic member foundation
In the case of elastic member foundations, you can manually enter spring constants.
Alternatively, you can use the various options to define the rotational and translational springs from a shear panel.
Member End Springs
RF-/FE-LTB calculates the individual spring constants automatically. You can use the dialog boxes and detailed pictures to represent a translational spring by connecting component, a rotational spring by a connecting column, or a warping stiffener (available types: end plate, channel section, angle, connecting column, cantilevered portion).
Member Hinges
If there are no member hinges defined in RFEM/RSTAB for the set of members, you can define them directly in the RF-/FE-LTB add-on module.
Load Data
The nodal and member loads of the selected load cases and combinations are displayed in separate windows. There you can edit, delete, or add them individually.
Imperfections
RF-/FE-LTB automatically applies the imperfections by scaling the lowest eigenvector.
In RF‑/LTB, the design is usually performed according to the equivalent member method according to DIN 18800, Part 2. However, you can specify extensive detailed settings for the design in a separate dialog box:
Design according to Bird/Heil
Optionally, it is possible to apply the method according to Bird/Heil in the program
the required shear stiffness Sreq
the lateral-torsional buckling load Nki
the critical buckling moment Mki
.
This plastic-plastic calculation method is only valid for lateral and torsional restraints with simple bending with simultaneous load introduction on the upper flange. Further requirements that must be met can be found in the program manual. In case of invalid conditions (for example, biaxial bending), RF-/LTB displays the corresponding error message. In addition, the reduction factorκM for the bending moments My can be set to 1.0 if a restrained rotation axis is present.
Non-Designable Internal Forces
It is possible to neglect non-designable internal forces and thus exclude them from the design if the quotient of the internal force and the fully plastic internal force falls below a certain value. This way, you can neglect, for example, a small moment about the minor axis, thus avoiding the method for biaxial bending.
Allowance according to DIN 18800, Part 2, Element (320) and Element (323)
Automatic determination of ζ
If you want the factor for the determination of the ideal elastic critical moment Mcr to be determined automatically, you can select one of the following types:
Solving the elastic potential numerically
Comparison of moment diagrams
Australian Standard AS 4100-1990
US standard AISC LRFD
When aligning the moment distributions, you can use the library which contains more than 600 moment distributions in tables.
The details for the lateral-torsional buckling analysis are defined separately for members and sets of members. The following parameters can be set:
Support Type/Lateral-Torsional Buckling Load
Available options are Lateral and torsional restraint, Lateral and torsional restraint or Cantilever
Special supports are possible by specifying the degree of restraint βz and the degree of warping restraint β0. In this section as well, you can consider the elastic warping restraint of an end plate, a channel section, an angle, a column connection, and a beam cantilever by specifying the geometry dimensions.
As an alternative, it is also possible to enter the lateral-torsional buckling load NKi or the effective length sKi directly
Shear panel
A shear panel can be defined from a trapezoidal sheeting, bracing, or a combination of these
Alternatively, you can enter the shear panel stiffness Sprov directly
Rotational restraint
Choose between continuous and discontinuous rotational restraint
Position of Positive Transverse Load Application
The z-coordinate of the load application point can be freely selected in a detailed cross-section graphic. (upper chord, lower chord, centroid)
Alternatively, you can specify the data by selecting them or entering the data manually.
Beam Type
For standard sections, the rolled beam, welded beam, castellated beam, notched beam, or tapered beam (web or flange welded) options are available
For special cross-sections, it is possible to directly enter the beam factor n, the reduced beam factor n, or the reduction factor κM
It is possible to select connection nodes graphically in the RFEM/RSTAB model. The relevant cross-section data and geometry are imported automatically. You can also define the parameters of hollow section connections manually. If necessary, you can modify the sections in the module.
The default angle between struts and chords can be modified as well. The geometric relation of the struts to each other is important for the correct choice of design. This relationship can be defined by specifying a gap between the struts or by overlapping them.